Technical Parameters Category Parameter Specification / Description General Model DVC6200HC Type Digital Valve Controller (High Capacity) Product Family FIELDVUE Primary Protocol HART Input & Output Input Signal 4 to 20 mA DC, two-wire Supply Pressure Up to 150 psig (10.3 bar) Performance (HC Output) Output Capacity Supply/Exhaust Flow: Up to 160 SCFM (4531 NLPM). This is the key specification, significantly higher than standard models (~40 SCFM). Steady-State Air Consumption ~0.04 SCFM (1.1 NLPM) Linearity ±0.5% of span Hysteresis Less than 0.3% of span Environmental Ambient Temperature -40°F to 185°F (-40°C to 85°C) Enclosure Rating Type 4X, 6 (IP66/67); Dust-tight and protected against water. Hazardous Area Certifications FM/CSA & ATEX/IECEx: Explosion-proof, Intrinsically Safe approvals for hazardous areas. Physical Conduit Openings Two 1/2" NPT Pneumatic Connections Supply & Output: Typically 1/2" NPT or 3/4" NPT to accommodate the high flow.

Technical Parameters Category Parameter Specification / Description General Model (Varies, e.g., part of a general catalog number) Type Bourdon Tube Pressure Gauge Performance Pressure Range 0 to 160 psi (may also have a dual scale in bar, e.g., 0-11 bar) Accuracy Standard: ±1.0% to ±2.0% of full scale. Dial Size Common sizes: 2.5", 4" (63mm, 100mm) Construction Case Material Stainless Steel or Phenolic (Plastic) Window Material Plastic or Safety Glass Bourdon Tube Material Brass (Standard), 316 Stainless Steel (for corrosive media) Connection 1/4" NPT Lower Back Connection (Standard) Environment Operating Temperature -20°F to 140°F (-29°C to 60°C) - depends on fill fluid.

Technical Parameters Category Parameter Specification / Description General Model DVC6200HC Type Digital Valve Controller (High Capacity) Product Family FIELDVUE Primary Protocol HART Input & Output Input Signal 4 to 20 mA DC, two-wire Supply Pressure Up to 150 psig (10.3 bar) Performance (HC Output) Output Capacity Supply/Exhaust Flow: Up to 160 SCFM (4531 NLPM). This is the key specification, significantly higher than standard models (~40 SCFM). Steady-State Air Consumption ~0.04 SCFM (1.1 NLPM) Linearity ±0.5% of span Hysteresis Less than 0.3% of span Environmental Ambient Temperature -40°F to 185°F (-40°C to 85°C) Enclosure Rating Type 4X, 6 (IP66/67); Dust-tight and protected against water. Hazardous Area Certifications FM/CSA & ATEX/IECEx: Explosion-proof, Intrinsically Safe approvals for hazardous areas. Physical Conduit Openings Two 1/2" NPT Pneumatic Connections Supply & Output: Typically 1/2" NPT or 3/4" NPT to accommodate the high flow.

Technical Parameters Category Parameter Specification / Description General Model 3661 Type Pneumatic Force-Balance Positioner (Double-Acting) Input & Output Input Signal 3 to 15 psi (0.2 to 1.0 bar) Supply Pressure Up to 100 psig (6.9 bar) Output Pressure Can approach supply pressure (e.g., up to 100 psig) on both outputs. Performance Linearity ±1% of span Hysteresis Less than 0.5% of span Air Consumption At Steady State: ~0.2 SCFM (5.7 NLPM) During Stroking: Higher, suitable for driving piston actuators. Output Capacity High, designed to fill and exhaust the volumes of typical piston actuators. Environmental Ambient Temperature -40°F to 175°F (-40°C to 80°C) Enclosure Rating Type 4X, 7, 9 (NEMA 4X, 7, 9); Weatherproof, dust-tight, and certified for hazardous locations. Hazardous Area Certifications FM/CSA: Explosion-proof (Class I, Div. 1, Groups B, C, D; Class II, Div. 1, Groups E, F, G). Physical Housing Material Aluminum with corrosion-resistant coating. Pneumatic Connections Supply & Outputs: 1/4" NPT Weight Approximately 15 lbs (6.8 kg)

Technical Parameters Category Parameter Specification / Description General Model 1098-EGR Type Double-Acting Scotch-Yoke Rotary Actuator Product Line RCS Classic Performance Torque Output The "E" in EGR specifies the actuator size, which determines its torque output. For size "E", the torque is approximately 900 lb-in (102 Nm) at an 80 psig (5.5 bar) supply pressure. Standard Rotation 90° (Standard). Other angles are available. Supply Pressure Typical operating range: 40 to 120 psig (2.8 to 8.3 bar). Action & Options Action The "GR" portion of the suffix defines the standard package. As a double-acting actuator, it requires air pressure to move in both directions and has no spring return. Positioner Mounting The "GR" package typically includes a bracket and linkage ready for the installation of a Fisher 1061 or similar pneumatic positioner. Construction & Environment Body Material Aluminum Temperature Range Standard: -20°F to 180°F (-29°C to 82°C) Corrosion Protection Epoxy coating.

Technical Parameters Category Parameter Specification / Description General Model 1301F Type Direct-Operated Pressure Reducing Regulator Pressure Ratings Maximum Inlet Pressure (P1) 5 psig (0.34 bar) Outlet Pressure Range (P2) Adjustable: Typically from 3" to 14" WC (0.75 to 3.5 kPa). Specific range is defined by the internal spring. Pressure Rating 125 psig (8.6 bar) Body Rating. Flow & Capacity Flow Capacity (Cv) Very Low, designed for pilot burners and small main burners. End Connections 1/2" NPT (Internal Pipe Thread) Materials & Environment Body Material Aluminum Internal Parts Stainless Steel, Brass Diaphragm Material Neoprene, fabric reinforced. Ambient Temperature Standard: -20°F to 150°F (-29°C to 66°C)

Technical Parameters Category Parameter Specification / Description General Model MR98H Type High-Thrust, Multi-Spring Pneumatic Positioner Input & Output Input Signal 3 to 15 psi (0.2 to 1.0 bar) Supply Pressure Up to 150 psig (10.3 bar) Output Action Double-Acting (Standard) Performance Output Capacity Extremely High. Specifically designed to supply and exhaust the large air volumes required by piston actuators. Significantly higher than standard positioners like the 3610J. Linearity ±1% of span Hysteresis Less than 0.5% of span Air Consumption Steady State: ~0.2 SCFM (5.7 NLPM) During Stroking: Very high, capable of flows over 10 SCFM. Environmental Ambient Temperature -40°F to 180°F (-40°C to 82°C) Enclosure Rating Type 4X, 7, 9 (NEMA 4X, 7, 9); Weatherproof, dust-tight, and certified for hazardous locations. Hazardous Area Certifications FM/CSA: Explosion-proof (Class I, Div. 1, Groups B, C, D; Class II, Div. 1, Groups E, F, G). Physical Housing Material Cast Aluminum with corrosion-resistant coating. Pneumatic Connections Supply & Outputs: 1/2" NPT (to accommodate high flow) Mounting Typically mounts directly onto Fisher 98L and other large piston actuators.

Technical Parameters Category Parameter Specification / Description General Model 3582G Type High-Gain Pneumatic Positioner Input & Output Input Signal 3 to 15 psi (0.2 to 1.0 bar) Supply Pressure Up to 100 psig (6.9 bar) Output Action Double-Acting (Standard for high-gain models to drive piston actuators). Performance Gain High. This is its defining characteristic, providing high sensitivity and fast response to input signal changes. Linearity ±1% of span Hysteresis Less than 0.5% of span Air Consumption Steady State: ~0.15 SCFM (4.2 NLPM) During Stroking: Higher, suitable for driving demanding actuators. Environmental Ambient Temperature -40°F to 180°F (-40°C to 82°C) Enclosure Rating Type 4X, 7, 9 (NEMA 4X, 7, 9); Weatherproof, dust-tight, and certified for hazardous locations. Hazardous Area Certifications FM/CSA: Explosion-proof (Class I, Div. 1, Groups B, C, D; Class II, Div. 1, Groups E, F, G). Physical Housing Material Aluminum with corrosion-resistant coating. Pneumatic Connections Supply & Outputs: 1/4" NPT Weight Approximately 11 lbs (5 kg)

Technical Parameters Category Parameter Specification / Description General Model 3720 Type Pneumatic Level Transmitter Performance Input Range Level range defined by the length of the float lever arm (e.g., 12", 24", 36", etc.). Output Signal 3 to 15 psig (0.2 to 1.0 bar) Supply Pressure 20 psig (1.4 bar) minimum, 20-35 psig (1.4-2.4 bar) typical. Accuracy ±1% of span Sensitivity 0.1% of span Mechanical Float Material Copper (Standard for water), Stainless Steel (for corrosive liquids). Lever Arm Length Standard lengths available to suit various tank depths. Mounting Typically side-mounted on the tank. Environmental Liquid Specific Gravity Typically designed for S.G. > 0.5 Ambient Temperature -20°F to 180°F (-29°C to 82°C) Enclosure Rating Weatherproof

Technical Parameters Category Parameter Specification / Description General Model 3582i Type Pneumatic Force-Balance Positioner (Indicating) Input & Output Input Signal 3 to 15 psi (0.2 to 1.0 bar) Supply Pressure Up to 100 psig (6.9 bar) Output Action Can be configured for Single-Acting (for spring-return actuators) or Double-Acting (for piston actuators). Performance Linearity ±1% of span Hysteresis Less than 0.5% of span Air Consumption Steady State: ~0.15 SCFM (4.2 NLPM) During Stroking: ~2.0 SCFM (56.6 NLPM) Environmental Ambient Temperature -40°F to 180°F (-40°C to 82°C) Enclosure Rating Type 4X, 7, 9 (NEMA 4X, 7, 9); Weatherproof, dust-tight, and certified for hazardous locations. Hazardous Area Certifications FM/CSA: Explosion-proof (Class I, Div. 1, Groups B, C, D; Class II, Div. 1, Groups E, F, G). Physical Housing Material Aluminum with corrosion-resistant coating. Pneumatic Connections Supply & Outputs: 1/4" NPT Weight Approximately 11 lbs (5 kg) Indicator Local mechanical gauge showing valve travel vs. signal.