Parameter Specification Manufacturer / Series Eaton / CV2 Part Number / Model CV2-20-P-0-5 Valve Type Two-Port, Pilot Operated Relief Valve (Screw-in Cartridge) Cavity Standard ISO 7368 (Size 20) Thread M45x2 Seal Kit Eaton E-KT-30 (or similar - confirm with latest datasheet) Function Pressure Control / System Relief Performance Nominal Size 20 Adjustable Pressure Range 0.5 to 5 bar (7 to 73 psi) [Critical Feature] Maximum Operating Pressure 350 bar (5,000 psi) Flow Capacity Up to 150 L/min (40 US GPM) - Flow is highly dependent on the low pressure setting and pressure drop. Refer to performance curves for accurate data at low pressures. Recommended Flow Range 5 to 150 L/min Hydraulic Fluid Mineral oil to ISO 11158 (HV46) or similar petroleum-based fluids. Fluid Temperature Range -20 °C to +80 °C (-4 °F to +176 °F) Fluid Viscosity Range 10 to 380 cSt (50 to 1800 SSU) Filtration Level Recommended: 25 µm absolute or better, per ISO 4406 code 19/17/14

Parameter Specification Manufacturer / Series Eaton / CV2 Part Number / Model CV2-20-P-O-100 Valve Type Two-Port, Pilot Operated Relief Valve (Screw-in Cartridge) Cavity Standard ISO 7368 (Size 20) Thread M45x2 Seal Kit Eaton E-KT-30 (or similar - confirm with latest datasheet) Function Pressure Control / System Relief Performance Nominal Size 20 Adjustable Pressure Range 10 to 100 bar (145 to 1450 psi) [Critical Feature] Maximum Operating Pressure 350 bar (5,000 psi) Flow Capacity Up to 150 L/min (40 US GPM) - Actual performance depends on pressure setting and pressure drop. Consult performance curves. Recommended Flow Range 5 to 150 L/min Hydraulic Fluid Mineral oil to ISO 11158 (HV46) or similar petroleum-based fluids. Fluid Temperature Range -20 °C to +80 °C (-4 °F to +176 °F) Fluid Viscosity Range 10 to 380 cSt (50 to 1800 SSU) Filtration Level Recommended: 25 µm absolute or better, per ISO 4406 code 19/17/14

Parameter Specification / Description Manufacturer / Series Eaton / EEA-PAM (Advanced Mobile Controller) Part Number / Model EEA-PAM-581-A-32 Product Type Programmable Mobile Electronic Control Unit (ECU) Microprocessor High-performance 32-bit RISC processor Memory Flash: 2 MB, RAM: 512 KB (Typical for this series) Communication Interfaces CAN Interfaces 2 x CAN 2.0B channels (ISO 11898) CAN Protocol J1939, Supported: UDS (KWP2000) for diagnostics Inputs / Outputs Analog Inputs Multiple, configurable (e.g., 0-5V, 5-0V, 0-32V) PWM Inputs Multiple, frequency configurable Digital Inputs Multiple, 24V capable Proportional Outputs Multiple PWM outputs for driving proportional soloids Digital Outputs Multiple low-side and high-side drivers (e.g., 5A rated) Sensor Supply 5V and 10V sensor supply outputs (short-circuit protected) Electrical Specifications Operating Voltage 9 - 32 V DC Load Dump Protection Yes, per ISO 7637-2 Reverse Polarity Protection Yes Environmental Specifications Operating Temperature -40 °C to +85 °C (-40 °F to +185 °F) Storage Temperature -40 °C to +105 °C Enclosure Rating IP6K9K (Dust and water tight, high-pressure/steam cleanable) Software & Programming Programming Tool Eaton EVI (Eaton Vehicle Interface) with CoDeSys-based environment Compliance ISO 11898, ISO 7637, ISO 16750, SAE J1939, CE Marked

Parameter Specification Manufacturer / Series Eaton / DG4V-3 Part Number / Model DG4V-3S-2A-M-FW-B5-60 Valve Type Solenoid Operated, Directional Control Valve Configuration 4-Port, 3-Position (4/3) Actuation Type Double Solenoid, Spring-Centered Spool Type 2A (This defines the internal flow path geometry in the actuated positions) Middle Position Float (FW) - In center position: P to T, A to T, B to T Mounting Style Subplate Mounting (ISO 4401-03 (CETOP 3) interface) Electrical Connection DIN 43650 Form A (with LED indicator and manual override) Coil Voltage -B5- typically denotes a 12V DC coil. Always confirm with supplier or datasheet. Protection Class IP65 (Dust tight and protected against water jets) Performance Nominal Flow Rate 60 L/min (15.8 US GPM) Maximum Operating Pressure 350 bar (5,000 psi) Solenoid Characteristics Solenoid Type Wet Pin DC Duty Cycle Continuous (Class F insulation system) Hydraulic Fluid Mineral oil-based hydraulic fluids to ISO 11158 (e.g., HV46) Fluid Temperature Range -30 °C to +80 °C (-22 °F to +176 °F) Fluid Viscosity Range 10 to 500 cSt (50 SSU to 2300 SSU) Filtration Level Recommended: 25 µm absolute or better, per ISO 4406 code 18/16/13 Weight (Approx.) ~2.0 kg (4.4 lbs) - (varies with coil and options)

Parameter Specification Manufacturer / Series Eaton / 93PM Part Number / Model 300AA00126A Product Type Three-Phase, Double-Conversion On-Line UPS Power Rating 300 kVA / 300 kW (Unity Power Factor, PF=1) Input Input Voltage 400 V AC (3Ph+N+E) Input Voltage Range Adjustable via dip switches (e.g., -15% to +10%) Input Frequency 50/60 Hz (Auto-sensing) Input Power Factor >0.99 Output Output Voltage 400/230 V AC (3Ph+N+E) Output Voltage Regulation ±1% Output Frequency 50/60 Hz (Synchronized to bypass within range) Output Power Factor 1.0 Battery Battery Voltage Typically 480 V DC (Specific string configuration required) Standard Battery Runtime Typically 5-10 minutes at full load (varies based on external battery cabinets) Performance Efficiency at Full Load Up to 96.5% in Double Conversion mode Efficiency in Eco Mode Up to 99% Physical & Environmental Form Factor Tower / Free-Standing Operating Temperature 0 °C to 40 °C (32 °F to 104 °F) Communication Interfaces Standard (X-Slot for network management cards, SNMP, USB) Standards & Certifications IEC 62040-1, CE Mark, UL, cUL, RoHS

Parameter Specification Manufacturer / Series Eaton / DG4V-3 Part Number / Model DG4V-3C-2C-M-U-H5-13 Valve Type Solenoid Operated, Directional Control Valve Configuration 4-Port, 3-Position (4/3) Actuation Type Single Solenoid, Spring-Centered (-3C-) Spool Type 2C (This defines the internal flow path geometry in the actuated position) Middle Position Closed Center (M) - In center position: All ports (P, T, A, B) are blocked. Mounting Style Subplate Mounting (ISO 4401-03 (CETOP 3) interface) Electrical Connection DIN 43650 Form A (with LED indicator and manual override) Coil Voltage -H5- typically denotes a 12V DC coil. Always confirm with supplier or datasheet. Protection Class IP65 (Dust tight and protected against water jets) Performance Nominal Flow Rate 13 L/min (3.4 US GPM) Maximum Operating Pressure 350 bar (5,000 psi) Solenoid Characteristics Solenoid Type Wet Pin DC Duty Cycle Continuous (Class F insulation system) Hydraulic Fluid Mineral oil-based hydraulic fluids to ISO 11158 (e.g., HV46) Fluid Temperature Range -30 °C to +80 °C (-22 °F to +176 °F) Fluid Viscosity Range 10 to 500 cSt (50 SSU to 2300 SSU) Filtration Level Recommended: 25 µm absolute or better, per ISO 4406 code 18/16/13 Weight (Approx.) ~1.8 kg (4.0 lbs) - (varies with coil and options)

Parameter Specification Manufacturer / Series Eaton / SG307 Part Number / Model SG307-F-55 Product Type Pressure Transducer (Strain Gauge) Pressure Type Gauge Pressure Pressure Range 0 to 350 bar 0 to 5000 psi Output Signal 4...20 mA (2-wire) (This is the standard output for this series) Supply Voltage 10...30 V DC Electrical Connection M12x1, 4-pin connector (Typical for "-F-" variant) Pressure Port G1/4" female (ISO 1179-2) (Typical, confirm with datasheet) Performance Full Scale Span (FSS) ±0.5% (Includes Non-Linearity, Hysteresis, Non-Repeatability) Null Offset ±0.5 mV/V Long-Term Stability < ±0.2% FSO per year Operating Conditions Proof Pressure 2 x Full Scale (700 bar / 10000 psi) Burst Pressure 3 x Full Scale (1050 bar / 15000 psi) Media Temperature -40 °C to +125 °C (-40 °F to +257 °F) Compensation Temperature -20 °C to +85 °C (-4 °F to +185 °F) Environmental Protection Class IP66 / IP67 (with connector mated) Media Compatibility Hydraulic fluids, oils, water, and other media compatible with 17-4PH SS and Viton.

Parameter Specification Manufacturer / Series Eaton / 9PX Part Number / Model 300AA00135A Product Type Single-Phase, Double-Conversion On-Line UPS (Tower) Power Rating 11 kVA / 11 kW (Unity Power Factor, PF=1) Input Input Voltage 230 V AC (1Ph + N + E) Input Voltage Range 115 - 286 V AC (Sag compensation up to 138 V) Input Frequency 50/60 Hz (Auto-sensing) Output Output Voltage 230 V AC (1Ph + N + E) Output Voltage Regulation ±2% Output Frequency 50/60 Hz (±0.5% in battery mode) Output Power Factor 1.0 Battery Battery Type Sealed, maintenance-free Lead-Acid (VRLA) Standard Battery Runtime Typical 5-10 minutes at full load (Varies with load and battery cartridge) Performance Efficiency at Full Load >96% Physical & Environmental Form Factor Tower Operating Temperature 0 °C to 40 °C (32 °F to 104 °F) Communication Interfaces USB, Serial (RS-232), SmartSlot (for network management cards like EBM) Standards & Certifications IEC 62040-1, CE Mark, cUL, RoHS

Parameter Specification Manufacturer / Series Eaton / ST307 Part Number / Model ST307-350-B Product Type Pressure Transmitter (Strain Gauge) Pressure Type Gauge Pressure Pressure Range 0 to 350 bar 0 to 5000 psi Output Signal 4...20 mA (2-wire) Supply Voltage 10...30 V DC Electrical Connection M12x1, 4-pin connector Pressure Port G1/4" female (ISO 1179-2) Performance Overall Accuracy (at 25°C) ±0.25% FSO (Includes Non-Linearity, Hysteresis, Non-Repeatability) Thermal Effects ±1.0% FSO (-20°C to +85°C) Long-Term Stability < ±0.1% FSO per year Operating Conditions Proof Pressure 2 x Full Scale (700 bar) Burst Pressure 3 x Full Scale (1050 bar) Media Temperature -40 °C to +125 °C (-40 °F to +257 °F) Compensation Temperature -20 °C to +85 °C (-4 °F to +185 °F) Environmental Protection Class IP66 / IP67 (with connector mated) Media Compatibility Hydraulic fluids (petroleum-based, HFA, HFB, HFC), water, air. Wetted parts: 17-4PH SS, seals: Viton (Standard).

Parameter Specification Manufacturer Eaton Part Number H-507848 Product Type Solenoid Coil (Wet Pin) Compatible Valves Designed for use with specific Eaton valves (e.g., DG4V series, etc.) Electrical Specifications Voltage 24V DC Duty Cycle Continuous (100%) Insulation Class Class F (155 °C) Power Consumption Typically ~22 W (Confirm with datasheet) Inrush Power Typically ~26 VA (Confirm with datasheet) Holding Power Typically ~20 VA (Confirm with datasheet) Electrical Connection DIN 43650 Form A Environmental & Physical Protection Class IP65 (Dust tight and protected against water jets) Ambient Temperature Range -40 °C to +120 °C (including coil hotspot) Features LED Indicator (Green), Manual Override Weight (Approx.) ~0.3 kg