Parameter Value / Description Product Name Eaton DGMPC-5-ABN-BAN-30 Product Line Eaton D4B / D4C Series (Heavy-Duty Limit Switches) Type Heavy-Duty Limit Switch with Maintained Contact Action Actuator Type Top Push Plunger with Roller Contact Configuration 2 Normally Open (NO) Contacts (This is the standard configuration for the "PC-5" contact block) Rated Operating Current 10 A at 600 V AC Rated Insulation Voltage 600 V Electrical Life 1,000,000 operations (at rated load) Mechanical Life 10,000,000 operations Degree of Protection IP65 (Dust-tight and protected against water jets) Electrical Connection Screw Clamp Terminals Housing Material Metal (Die-cast zinc) Operating Temperature -25 °C to +85 °C (depending on seal material) Pretravel The distance the plunger moves from its free position to the operating point. (Specific value requires datasheet, e.g., ~4.8mm). Overtravel The distance the plunger can travel beyond the operating point. (Specific value requires datasheet). Operating Force The force required to actuate the plunger (Specific value requires datasheet, e.g., ~3.5 N). Reset Force The force exerted by the internal spring to return the plunger. Standards Compliance IEC/EN 60947-5-1, UL 508, CSA C22.2 No. 14

Parameter Specification Notes Series DGMDC-5 Output Power 30 W Continuous Input Voltage (Vin) 4.5 - 5.5 VDC Wide Range Output Voltage (Vout) 13.8 VDC Nominal Output Current (Iout) Up to 2.17 A At full load Efficiency Typically 89% At nominal input, full load Isolation 1500 VDC Input to Output Input-Output Ripple & Noise < 50 mVp-p Typical, 20MHz bandwidth Line Regulation ±0.5% For full input range change Load Regulation ±0.5% From 10% to 100% load Operating Temperature -40°C to +100°C With derating above ~85°C Storage Temperature -55°C to +105°C Package / Mounting Through-Hole (Pin-in-Paste) "TN" Style Dimensions (L x W x H) Approximately 33.0 x 22.6 x 10.2 mm Safety Standards UL/EN/IEC 60950-1 Or equivalent EMC Complies with EN 55032 (FCC Part 15) Class B Typically with external filter

Parameter Specification Notes / Explanation Model Series DG4V Valve Size 03 CETOP 3, NFPA D01 Mounting Interface ISO 4401-03 NFPA D01, H7 Option Number of Ports 4 (P, T, A, B) Number of Positions 3 Actuation Type Solenoid Operated, Hydraulic Pilot Requires pilot pressure Solenoid Type Wet Armature DC Maximum Operating Pressure 350 bar (5,000 psi) Maximum Flow Capacity ~ 45 L/min (12 US gpm) Dependent on spool type and pressure drop Pilot Pressure Range 17 - 35 bar (250 - 500 psi) minimum Required for spool shifting Internal Pilot Supply From 'P' port Return Spring M Spring-centered to neutral position Manual Override U With manual override (standard) Seal Material Standard: Nitrile (Buna-N) Optional Viton available

Parameter Specification (Estimated) Notes Product Type Thermal Overload Relay For 3-phase AC motor protection Series Likely part of the Eaton DILER or Meme series Adjustable Current Range e.g., 2.5 - 8.2 A Allows setting to match motor FLC Rated Insulation Voltage (Ui) 690 V / 750 V Rated Operational Voltage (Ue) 690 V AC Compatible Contactors Designed to match specific Trip Class Class 10 Standard trip characteristic (7-10 sec at 600% current) Ambient Temperature -20°C to +60°C Operation without derating Standards IEC/EN 60947-4-1, UL 508, CSA C22.2 Reset Mode Manual or Automatic Selectable Auxiliary Contacts Normally Closed (NC) + Normally Open (NO) For control circuit signaling (e.g., trip indication)

Parameter Specification (Estimated) Notes Product Type Thermal Overload Relay For 3-phase AC motor protection Series Likely part of the Eaton DILER or Meme series Same series as 300AA00382A Adjustable Current Range e.g., 2.0 - 6.3 A Fine-tuned to match the protected motor's FLC Rated Insulation Voltage (Ui) 690 V / 750 V Rated Operational Voltage (Ue) 690 V AC Compatible Contactors Designed to match specific Trip Class Class 10 Standard trip characteristic (7-10 sec at 600% current) Ambient Temperature -20°C to +60°C Operation without derating Standards IEC/EN 60947-4-1, UL 508, CSA C22.2 Reset Mode Manual or Automatic Selectable Auxiliary Contacts Normally Closed (NC) + Normally Open (NO) For control circuit signaling (e.g., trip indication)

Parameter Specification Notes / Explanation Series 2CFR Rated Current 30 A Rated Voltage 250 VAC / 50-60 Hz For single-phase systems Rated Voltage (DC) 350 VDC Leakage Current < 3.5 mA Typical at 250VAC / 50Hz Test Voltage (Hi-Pot) 2250 VAC (Line-Line) 1500 VAC (Line-Ground) For 1 minute Operating Temperature Range -25°C to +100°C With derating above +40°C Termination Style Screw Terminals Housing Material Metal (Shielded) Standards & Approvals Complies with EN/IEC 60939 UL 1283 recognized, CSA certified Mounting Through-hole or bracket

Parameter Specification Notes / Explanation Model Series DGMPC Kepner Proportional Control Valve Valve Size 3 Nominal size, e.g., 3/4" NPT ports Number of Sections 2 Indicated by -ABK- and -BAK- Actuation Type Manual Lever Spring-centered return Maximum Operating Pressure Up to 350 bar (5,000 psi) Maximum Flow Capacity ~ 75 - 110 L/min (20 - 29 US gpm) Port Size Typically 3/4" NPTF Inlet Section Features Includes Relief Valve & Power Beyond "41" code typically indicates this Leakage Classification Industrial Seal Material Standard: Nitrile (Buna-N)

Parameter Specification Notes / Explanation Model Series CV1 Port Size 1/8" NPT "16" in the model number typically corresponds to 1/8" Number of Ports 5 (1-Pressure, 2-Exhaust, 2-Work ports A & B) Number of Positions 3 Actuation Type Solenoid Operated, Air Pilot Spool/Center Position Closed Center (All Ports Blocked) This is the "P" type in the model code Voltage Must be specified Common options: 12 VDC, 24 VDC, 120 VAC, 240 VAC Operating Pressure Range 30 - 120 psi (2 - 8 bar) Typical for pneumatic valves Maximum Flow (Cv factor) ~ 0.5 Response Time ~ 20 - 50 ms Duty Cycle 100% Continuous Mounting Style Sub-base / Manifold Mount ISO 5599-1 standard Seal Material Standard: Nitrile (Buna-N) Coil Connection Conduit or DIN Form A With LED indicator

Parameter Specification Notes Manufacturer / Series Eaton DG4V / DG3V D03 / NG6 interface Model Number DG4V-3-2A-M-U-H7-69-EN124 Valve Type Directional Control Valve Number of Ways / Positions 4-Way, 3-Position Porting Size D03 (NG6) ISO 4401 standard Port Thread 7/16"-20 UNF Common for D03 size Actuation Type Solenoid Operated, Spring Return Solenoid Type Single Solenoids (2x) Wet-pin, DC versions Center Position 2A: All Ports Blocked (Closed Center) "A", "B", and "P" to "T" are blocked. Spool Type "-69" Specific metering and performance characteristics for PTO/EN124 applications. Electrical Connection -H7: DIN 43650 Form A IP65-rated connector with LED indicator and manual override. Voltage Options Typically 12 VDC or 24 VDC Must be specified when ordering. Maximum Operating Pressure 350 bar (5,000 psi) Maximum Flow Rate ~ 20 L/min (5.3 US gpm) Dependent on spool type and pressure drop. Fluid Viscosity Range 10 to 380 cSt (50 to 1800 SUS) Fluid Type Mineral-based hydraulic oils, synthetics Compatible with standard hydraulic fluids. Temperature Range -20°C to +80°C (-4°F to +176°F) For hydraulic fluid. Compliance / Standard EN124 European standard for controls of vehicle PTOs. Seal Material Nitrile (NBR) Standard. Other options (e.g., FKM) may be available.

Parameter Specification Notes / Interpretation Manufacturer / Series Eaton CGR Cartridge Check Valve, Pilot Operated Model Number CGR-02-F-K-30 Valve Type Pilot-Operated Check Valve Cartridge Style CETOP C-02-2 ISO 7368 standard cavity. Critical for installation. Port Size #12 SAE O-ring Adjustment Type K-30: Cracking Pressure Adjustment Features an external screw for setting the pilot cracking pressure. Pilot Ratio 4:1 (typical for CGR-02) The pilot pressure required is approximately (System Pressure / Pilot Ratio). Maximum Operating Pressure 350 bar (5,000 psi) Maximum Pilot Pressure 210 bar (3,000 psi) Cracking Pressure Adjustment Range 1.7 to 14 bar (25 to 200 psi) The range over which the pilot opening pressure can be set. Flow Capacity Up to 75 L/min (20 US gpm) Dependent on pressure drop. Seal Material Nitrile (NBR) Standard. Other options like Fluorocarbon (FKM) may be available. Body Material Steel